Hi Sree,
Can you please clarify regarding whether the previous reply I provided here helps you.
Thanks & Regards,
Sapna
Hi Sree,
Can you please clarify regarding whether the previous reply I provided here helps you.
Thanks & Regards,
Sapna
Olá Félix,
A BADI que usamos para conversão de unidade de medida, faz basicamente um "de-para" ou seja ("de = UM do XML" e "para = UM do SAP"). Feito isto, o resto deveria funcionar. Se não está funcionando, possivelmente a CUNI do GRC e/ou do ECC não está correto para a UM, Confirme também se está correto para o idioma utilizado e se ambos tem o código ISO corretamente informado.
Se tiver ok na transação CUNI tanto no GRC, como no ECC, a conversão deveria ocorrer de acordo com a conversão atribuída no mestre de material.
Nos projetos que passei, resolvemos seguindo esta ordem.
Att,
Bruno Duarte
Olá Everton,
Eu tive este erro há um tempo e o problema estava justamente na NF-e de referencia (de saída - mov. 541). No meu caso, a chave de acesso da nota de saída não estava correta no XML e por isto, o sistema não achou a saída para então fazer o retorno (mov. 542).
Assim, como sugestão, tenta verificar se realmente se trata de uma NF-e ou NF comum (mov. 541)...e se no XML está corretamente informado no campo específico tal NF ou NF-e.
Fora isto, não tenho outra dica...
Boa sorte!
Att,
Bruno Duarte
hi,
In pricing procedure statistical tick should be there or not ? When I am going for main vendor miro It is going to pay full amount (Material cost + freight ) & not allow to do different miro for main vendor & Freight vendor.
Hi everyone,
looking for a bit of guidance of EV calculation from an SKF POC.
I've setup the following structure:
The version Z01 is using EV basis as Weighted
The following has been carried out:
When running CNE1 the POC is calculated however plan/actual EV BCWS BCWP is not showing in the EV reports.
If I change the version and MM to Estimation on the L1 L2 WBSs and update the POC in CNPAWB these are calculated.
Any pointers would be great.
Cheers
Hi Uday,
You seem to be in right track. Did you put a remote breakpoint in your RFC and check what is happening?
And what is the response at Rest Client for a Create request?
Thanks
Krishna
Dear Ruben Nogueira,
Can you please clarify regarding whether the previous reply I provided here helped you.
Thanks & Regards,
Sapna
Message was edited by: Sapna J Kini
Hi Gurus,
I really need your help... some of QUERY fields should be invisible for some user-id, how can I achieve this? or another suggestion...
Thanks for any help.
Jamie
Hola, Johanna.
Te recomiendo ajustar un poco el query para que quede de la siguiente forma:
if qtransaction_type in ('A' and @objec_type = '13' BEGIN declare @líneas int set @líneas = (Select count('A') from INV1 T0 where T0.DocEntry = @list_of_cols_val_tab_del) if @líneas > 15 begin Select @error = 1, @error_message = 'Tu mensaje de error' end end
Esto, ya que existe la posibilidad de que los usuarios puedan eliminar filas y luego agregar más, y esto provocaría que el LineNum pierda su consecutivo, entonces es recomendable contar las filas en lugar de leer el LineNum.
Espero te sea de utilidad.
Saludos,
Juan Carlos.
Dear Vansai,
Thank you for reply .
But when I excuted WEBI rich client with Administrator , same error was occured .
And I have two server . The one is BO server that has BOBI Platform Server 4.0 SP5 and BOBI Platform Client tool 32bit 4.0 SP5 . The other is Modeling server that has BOBI Platform Client tool 32bit 4.0 SP5 .
When I excuted WEBI rich client in BO server , the error was not occered . But when I excuted WEBI rich client in Modeling server , the error was occered . The same CMC is used in BO server and Modeling server .
I apologize for being late to notice to you about this .
Thanks & BR
Kazuki
Hi JRK Prasad
Thanks for your reply, could you please include the web.xml file? It wasn't attached in your reply.
Thanks in advance,
Teresa
Dear Jawahar,
Thank you for reply .
But when I excuted WEBI rich client with Administrator , same error was occured .
Thanks & BR
Kazuki
Hi,
I am not too sure what you offered? I replied to your request on what service pack I was running and have not heard anything from you since.
Someone called n c asked for my source code, which I did not feel was relevant because they were talking about ASP.net, not WPF.
The stack trace clearly shows that the exception is occurring in SAPBusinessObjects.WPF.Viewer code.
I have provided clear steps in my initial post on how to produce this bug, I am sure your QA team have a WPF project they can run to test this, it will take less than 5 minutes to reproduce.
Thanks
Anthony
Hi Danie,
I have mentioned already that I have a work around for this. Thanks anyway.
Arun J
Hi,
The functionality is available with LORD2 only starting from ECC EHP4.
To make the activity transaction type available, you have to activate the copy control for activities at
SPRO
-> Customer Relationship Management
-> Transactions
-> Settings for Activities
-> Activate Copying Control for Activities
Best regards,
Maggie
Hi Hans,
From the logs it appears that write activity for a remote database is failing. Could you check whether there is enough space in the tablespaces for remote database specified in dbcon.
Hope this helps.
Regards,
Deepak Kori
Юлия добрый день,
Есть такая штука называется Partner Schema, Partner Determination это определение партнёров.
По дефолту Менеджер там не доступен но! никто не мешает вам его туда добавить.
Далее выбирать уже по нему.
Далее выбираем Схему партнеров 00000032 Installed Base/IBase - Partner Functions in Procedure
Новые записи далее вам будет понятно.
Как сделаете отпишите и наверное давайте лучше на английском ато нас могут забанить
Не беспокойтесь мы обязательно разберёмся !
The requirement seems to be:
Upon completion and saving of the Preventive maintenance Notification, another Notification should trigger with:
1. The activity you want as Notification title and
2. Required start date, time (STRMN, STRUR) as 125hrs + the above completion time.
Jogeswara Rao K
Hello Luis,
Hope you are doing great!
Is there any difference in organisation profile assigned to both document types?
Regards,
Caíque